Differences

This shows you the differences between two versions of the page.

--- en:projects:mmt4ue2:start [2014-11-07 17:57] – [The MMT4ue2] mka
+++ en:projects:mmt4ue2:start [2016-09-20 20:27] (current) – [Drivers of this project] mka
@@ Line 14: / Line 14: @@
 And then you can just do such things: \\
-[[http://youtu.be/Q3OD7Edfhwg|Dance of the Servos]]
+[[http://youtu.be/Q3OD7Edfhwg|EX6 - Dance of the Servos]]
-[[http://youtu.be/s-9q_lnT7zQ|Toggle 4 OUT bits manually]]
+[[http://youtu.be/s-9q_lnT7zQ|EX5 - Toggle 4 OUT bits manually]]
-[[http://youtu.be/mKblxqHwhjQ|Servo follows analog input pin (ADC4)]]
+[[http://youtu.be/mKblxqHwhjQ|EX7 - Servo follows analog input pin (ADC4)]]
+The board TI Launchpad has been used for design and programming.
+For an application use the EuroTech MSP430Board,
+LED and switches onto the little Protoboard,
+USBtoSerial cable to the PC if wanted.
+That’s it.
+Or control some features only by the three buttons – then you need 2 AAA cells for power
 ==== Design of the electronic Mini Multi Tool ====
@@ Line 42: / Line 52: @@
 ==== The two MiniPCBs ====
-They are described very quickly: They actually consist of MCU, whose pins are taken to the outside of the board, so solder connections can be made easily and changed again and again. Or add two pin headers, soldered in to plug the whole thing into a breadboard (see picture). And combinations are possible. On this board there are only the minimum necessary components for the operation of the MCU of this MultiTool.The whole system is assembled quickly, reusable; and as it is extremely low cost, it can also be installed, another one built and used as intelligent IO, or tested to death during experimenting.
+They are described very quickly: They actually consist of MCU, whose pins are taken to the outside of the board, so solder connections can be made easily and changed again and again. Or add two pin headers, soldered in to plug the whole thing into a breadboard (see picture). And combinations are possible. On this board there are only the minimum necessary components for the operation of the MCU of this MultiTool.The whole system is assembled quickly, reusable; and as it is extremely low cost, it can also be installed, another one built and used as intelligent IO, or tested to death during experimenting. You may shrink your Forth computer down to a chip with software, one resistor, a few wires, and FTDI 3.3VUSB Interface.
+Or make your own [[en:projects:mmt4ue2:urchin|urchin]] ...
 {{:projects:mmt4ue2:2014-10-17_10.27.15.jpg?200|Left half: MiniPCBs – top and bottom side. Right half: The complementary experimental PCB to add additional parts.}}
 {{:projects:mmt4ue2:2014-11-04_21.58.07.jpg?200|Both boards soldered together.}}
+{{:projects:mmt4ue2:2014-11-08_10.20.00.jpg?200|With mini I/O-module - and MCU without any PCB ...}}
 {{:projects:mmt4ue2:minipcb1-msp430g2553.jpg?100|This little PCB is for MCU ... }}
@@ Line 64: / Line 78: @@
 ==== Source Code ====
-Can you join in already now? Of course you can. The [[projects:mmt4ue2:mmtquellcode0|source code]] is not fully finished yet, but if you want to, you can look at the code and run it. There will certainly still be minor changes. Or other ideas later.
+Can you join the user club already? Yes, you can. The source code is not fully developed yet, but if you want [[projects:mmt4ue2:mmtquellcode0| have a look already]].
+You do not have to copy from the preview, just download the {{:projects:mmt4ue2:mmt4ue2.zip|starter pack}} to join. It contains the immediate flash-ready image of MMT4 , and as documentation the source code.
-And it is already clear that this will make a 4e4th-update necessary. Because the Mini Multi Tool was started under 4e4th-rev034, there are some inconsistencies with the 4e4th IDE. In this new IDE there is already the debug version in use.
-The {{:projects:mmt4ue2:mmt4ue2.zip|starter package to get involved}} is still quite rudimentary. But do not bother, it will work out. 8-)
+There will be certainly still minor changes. And it is already clear, this asks for a 4e4th update. The Mini Multi Tool was started under 4e4th - rev034 , which results in some inconsistencies with the current 4e4th IDE. The IDE does use some debug capabilities already of the 4e4th.
 ==== Updates ====
@@ Line 92: / Line 104: @@
 [[projects:4e4th:4e4th:start:msp430g2553_experimente|Grundlegende Experimente mit MCUs ( English version to follow )]]\\
 [[http://www.4e4th.eu/|4e4th und 4e4th-IDE]]\\
+{{:en:projects:microbox:4e4th-ide-startnotes_2016_03_29_a5_v1.pdf|4e4th Start Notes}} - First stepps...\\
+{{:en:projects:microbox:4e4th-ide-instructions_including_microbox_a5_2016_03_29_v1.pdf|4e4th Instructions, including Microbox}} ... more details\\
 [[http://www.mpeforth.com/xc7lite.htm|VFX Forth Lite cross compilers von MPE]]\\
@@ Line 99: / Line 113: @@
 And thanks to others who helped. Pick up your free boards at** electronica 2014, 11 - 14 November at EuroTech**.
@@ Line 111: / Line 130: @@
 {{:projects:mmt4ue2:forth_mini_multi_tool_for_your_embedded_experiments_v1_2014_11_06.pdf|Intermediate result of this website.}}
+==== Various ====
+{{:projects:mmt4ue2:mybonnie.png?400|The notes of the song.}}